Комплект рулевых для Jeep Link Kit 3/4 болты дюйма от GenRight

611

Комплект рулевых для Jeep Link Kit 3/4 болты дюйма от GenRight

186 200 р. / шт

Уточняйте актуальную стоимость у менеджера. Она может быть ниже указанной.

Под заказ

Расчётное время доставки:
20/06/24 — 20/07/24

- +

В корзину

Количество

Срок доставки рассчитывается, согласно статистики доставленных международных заказов. Не учитываются задержки производителя с отправкой заказа, задержки на таможне и другие, не зависящие от нас обстоятельства. Указанный период не может являться 100% сроком доставки, хотя при благоприятных обстоятельствах может быть доставлен и раньше. Расчетный срок доставки является ориентировочным для доставки Вашего заказа на склад в Москве. Если срок затягивается, не переживайте, Ваш заказ приедет, но чуть позже ;)

Добавить в список желаний

Как только товар будет в наличии Вы получите уведомление на почтовый e-mail

Есть вопросы? Задайте их специалисту:
8-800-555-78-01

Описание:

This is the GenRight "builders" steering (Drag Link and Tie Rod) kit. It is a perfect compliment to our Front 3 Link suspension kit and can be cut to fit any vehicle (including a Jeep TJ, LJ, CJ or YJ) or axle width and works best with hi-steer type knuckles. This kit is made up of the best component parts you can buy for on-road OR off-road use! This Heavy Duty kit will hold up to big tires and off-road abuse. Got a hydraulic ram? It will work with that too.
Our kit includes:

(1) Thick wall 1-3/8" diameter Heat Treated CrMoly Tubing (for the tie rod)
(1) Thick wall 1-3/8" diameter DOM Tubing (for the drag link)
(4) Heavy Duty 7/8" diameter threaded shank FK CrMoly Heim rod ends and jam nuts
(4) Left & Right hand threaded tube inserts (for easy adjustment)
(8) CNC Machined stainless steel safety washers (for the top and bottom of each rod end)
(4) Heavy Duty 3/4" Grade 8 mounting hardware
Why Heim rod ends? We prefer the heims over the standard or heavy duty "tapered style" tie rod ends because, over the years we have seen the taper on the tie rod end SPLIT too many steel knuckles! This is the exact same steering set up we have used on our GenRight rigs for years, and it works great!

Important Notes:
Cutting & Welding is required: This kit requires cutting the tubing to length (tailoring it to your specific vehicle) and welding the threaded inserts onto the end of the Drag Link and Tie Rod.
This kit may also require pressing out the ball joints to remove them from the stock knuckles, so you'll need a ball joint press if you are a do-it-yourselfer.
This kit is offered in (2) sizes 3/4" for Dana 60 axle knuckles and 5/8" for Dana 44's & 30 knuckles. If necessary please order the smaller 5/8" GenRight CrMo Hi-Steer Kit (STK-8625)
To install this GenRight CrMo Hi-Steer Kit it will require drilling the taper out of the knuckle with a 3/4" diameter drill.
This kit requires moving the axle side trac bar mounting location to match the new higher drag link position!!!
Once Installed, you MUST cycle the front suspension and steering (in all possible direction combinations) to make sure the ball joints or heims DO NOT exceed their range of motion which would damage the steering components and could cause a failure resulting in a loss of steering control!